DOWNLOAD AHS AHERACTIVE AND THE LATEST OFFERS ARE AT YOUR FINGERTIPS.
Global Precision Industrial Mold News Center
Insights in Smart Molding, Empowering Green Logistics & Daily Living
Focusing on the latest technology breakthroughs, T1 trial deliverables, and industry standard analyses for turnover boxes, pallets, storage cabinets, and daily commodity molds.
500+
Annual Mold Output
40+
Global Client Countries
98.5%
T1 First-Trial Pass Rate
35+
Senior R&D Engineers
Featured Breaking News
★ FeaturedTechnology
2026-10-06 3,420 Views

Breakthrough in Core Technology for Ultra-Large 3-Runner Pallet Gas-Assisted Injection Molds — Driving Global Smart Warehousing Cost Reduction

Addressing the high-strength turnover and lightweight requirements of modern smart warehousing, our technical team spent six months researching and overcoming the challenges of thick-wall shrinkage and gas channel balance. We successfully delivered the first ultra-large 3-runner pallet gas-assisted mold in China, reducing the molding cycle by 22% and increasing load strength by 40%...

  • Technical Article
  • Mold Design
  • Mold Processing
  • Injection Molding Process
  • Material Selection
文章附图

Why Does Material Decompose If It Stays in the Barrel Too Long?

2026-10-09
Why Does Material Decompose If It Stays in the Barrel Too Long?In injection molding production, there is a type of defect that is very difficult to troubleshoot: the product intermittently shows bl...
Mold Technical Material Selection
文章附图

Why Does an Excessive Regrind Ratio Cause Strength Reduction?

2026-10-09
Why Does an Excessive Regrind Ratio Cause Strength Reduction?In injection molding production, the use of regrind is an unavoidable topic. Sprue material, rejects, and edge trim, once ground up and ...
Mold Technical Material Selection
文章附图

Why Does PP Usually Not Require Drying, While PA Must Be Dried?

2026-10-09
Why Does PP Usually Not Require Drying, While PA Must Be Dried?On the injection molding floor, the arrangement of the drying step often confuses people: PP (polypropylene) pellets are poured out of...
Mold Technical Material Selection
文章附图

Why Does Inadequate PC Drying Cause Silver Streaks?

2026-10-09
Why Does Inadequate PC Drying Cause Silver Streaks?The silver streak problem in PC (polycarbonate) is arguably one of the most classic—and most easily misdiagnosed—defects on the injection molding ...
Mold Technical Material Selection
文章附图

Why Must Certain Materials Be Dried Before Injection Molding?

2026-10-09
Why Must Certain Materials Be Dried Before Injection Molding?On the injection molding floor, there is one step that seems like "unnecessary extra work": plastic pellets that look dry and feel dry t...
Mold Technical Material Selection
文章附图

When Do Problems Surface: Incorrect Barrel Temperature Zone Settings?

2026-10-09
When Do Problems Surface: Incorrect Barrel Temperature Zone Settings?Incorrect barrel temperature zone settings are a problem in injection molding that is "neither too big nor too small." Not too b...
Mold Technical Injection Molding Process
文章附图

Why Does Insufficient Clamping Force Cause Mold Bulging, While Excessive Clamping Force Causes Poor Venting?

2026-10-09
Why Does Insufficient Clamping Force Cause Mold Bulging, While Excessive Clamping Force Causes Poor Venting?In injection molding, clamping force is a parameter that "pleases no one." Set it too low...
Mold Technical Injection Molding Process
文章附图

Why Does Increasing Mold Temperature Sometimes Improve Weld Lines but Sometimes Worsen Sink Marks?

2026-10-09
Why Does Increasing Mold Temperature Sometimes Improve Weld Lines but Sometimes Worsen Sink Marks?In injection molding, mold temperature is a parameter that people both love and hate. Raise the mol...
Mold Technical Injection Molding Process
文章附图

What Are the Machining Difficulties of Multi-Cavity Molds for Plastic PET Buckets?

2026-10-08
What Are the Machining Difficulties of Multi-Cavity Molds for Plastic PET Buckets?Multi-cavity molds for PET buckets (or large preforms) are among the more difficult categories in mold machining. U...
Mold Technical Mold Processing
123

total 3 pages

to page

Subscribe to Mold Tech Insights
Get weekly updates on injection mold technology analyses, exhibition invites, and whitepapers.

  • Sign up for our newsletter*

WhatsApp：Lynn
WhatsApp：Jack
Email：Contact Us